SPECIFICATIONS FOR JN01S-CH

List For Wire Kinds

 

 

Model

Wire Size

AWG

UL1007

#30

#28

#26

#24

#22

#20

#18

#16

#14

mm2

  

0.05

0.08

 0.12

 0.2

 0.3

 0.5

  0.85

1.25

2.0
JN01S-CH-FX30

 

 Max outer dia. of wire should be up to Ø1.4

            
 JN01S-CH-FX

 

  

 Max outer dia. of wire should be up to Ø1.4

          
 JN01S-CH-FN

 

      

Max outer dia. of wire should be up to Ø1.8

      
 JN01S-CH-ST

 

        

 Max outer dia. of wire should be up to Ø3.5
 Model  JN01S-CH-FX30  JN01S-CH-FX    JN01S-CH-FN   JN01S-CH-ST
 Function Measuring - Cutting - Both ends stripping - Both ends crimping - Single end crimping - Single end soldering - Auto-blade depth adjustment - Auto-crimping position - Auto-strip length - Half-strip on both ends crimping - Inferior products selection device - Step driving - Both end half-strip
Capacity  Both end crimping: 1.0 sec/pc - Crimping and soldering: 1.3 sec/pc Both end crimping: 0.9 sec/pc - Crimping and soldering: 1.3 sec/pc - Crimping and soldering: 1.6 sec/pc Both end crimping: 0.8 sec/pc (Min. wire length) - Crimping and soldering 1st row half: 1.2 sec/pc(Min. wire length) - Crimping and soldering 2nd row half: 1.5 sec/pc (Min. wire length)
Wire Size  0.05~0.12mm2 (AWG#30~#26 UL1007 equivalent) call Toyojamco in case of special wire - UL1571 straded many wires. 0.08~0.12mm2 (AWG#28~#24 UL1007 equivalent) 0.2~0.5mm2 (AWG#24~#20 UL1007 equivalent) 0.3~2.0mm2 (AWG#22~#14 UL1007 equivalent) - call Tojoyamco in case of special wire
Cutting Length   35~5,000mm (9,999mm) - Cutting length depends on pre-feeder
Cutting Accuracy   Variation within 1mm+ (set length x 0.002)
 Stripping Length No. 1 side: 1.5~17mm - No. 2 side: 1.5~10mm No. 1 side: 1.5~17mm - No. 2 side: 1.5~17mm No. 1 side: 1.5~17mm - No. 2 side: 1.5~25mm
 Soldering Length  2~10mm  2~17mm
 Cut Depth  2mm (100 STEP: 1 STEP=0.02mm) - Max Adustment 2mm
Press Capacity   19,600N (2 TON x 2) low noise type
 Detector Low air pressure - Crimping miss - Wire stripping miss - Abnormal action of wire reel stand - Terminal presence
 Power Source  AC200V (within ± 10%) 50/60Hz single phase 10A
 Compressed Air  0.5Mpa (5kgf/cm2) approx. 290NL/min (use clean dry air)
Temperature   15~25°C (Circumstances) 30~80%RH (Humidity)
 Dimension - Mass  1,700W x 770D x 1,450H (mm) - (approx. 600kg)
Option  Wire reel stand (bundle, reel) - Wire pre feeder (2m, 5m) - Paper winding unit - Belt chute - Wire joint detector - Manual crimp height device - Simplified crimp pressure control device - Central control system - Servo crimper (19600N) - Auto-crimp height device (designing) - Multi reel stand - Inferior products selection device - Discharging after selection - Emergency light ASY - Other makers applicator conversion kit
 Special Option FXASY soft wire FX-30ASY soft wire  STASY, ASY - big wire  FNASY, ASY - big wire